About BMS
This BMS product is for customers who have bought lifePO4 batteries. If they choose and buy BMS suitable for them under the advice of the seller, we will send them out normally.
Special case: If the buyer did not buy the battery from LANpwr, but only bought the BMS, please confirm that the BMS is suitable for your own battery before purchasing, and we will not take any responsibility for the buyer's wrong purchase.
16S 100A BMS Product Parameters | |||
Function | Communication Interface | LiFePO4/LFP/Lithium iron phosphate | |
Number of battery cells | 16 | ||
Resistance value of current sense resistor | 0.2mΩ | ||
Storage | Store 10000 records | ||
Charge current limit | Enabled by default | 20A Definition: When the charging current>100A, turn on the 20A current limit, enter the current limit until the end of charging, and the charging current has interrupt logic to re-detect and judge. |
|
Display screen | Yes | English 4-key display screen, default none, can be customized | |
Dry contact | Yes | Passive dry contact Dry contact 1-PIN1 to PIN2: normally open, closed in case of fault and protection; Dry contact 2-PIN3 to PIN4: normally open, close when low battery alarm. |
|
Heating film | Yes | Need to customize Definition: Start heating when the minimum temperature of the battery core is lower than 5°C during charging, and stop heating when the minimum temperature of the battery core is higher than 15°C. |
|
Reverse polarity protection | None | ||
Weak current switch | Yes | Ship-type self-locking switch, with the highest status authority, corresponding to the ON/OFF indicator light. | |
Buzzer switch | Off by default | The BMS is turned off by factory default and can be turned on through the host computer. | |
Location function | None | ||
Sampling socket | Vertical | ||
DIP switch | 4 bit | ||
LED lights | Nine | ALM、 RUN 、ON/OFF、 SOC、 6 | |
Current sense resistor | Ten | ||
Cell capacity | 100A | ||
Voltage | 51.2V | ||
Barcode | QR code | ||
Anti-theft function switch | None | ||
Environmental requirements | Operating temperature | -20°C to 75°C | |
Storage temperature | -40°C to 75°C | ||
Working humidity | ≤95%RH(45℃±2℃) | ||
Storage humidity | ≤95%RH(45℃±2℃) | ||
Temperature measurement | -40°C to 125°C | ||
Atmospheric pressure | 70kPa to 106kPa |
16S 100A BMS Communication Instructions | ||||
Communication Interface | RS232 | RS485 | CAN | Parallel dual RS485 |
Upgrade method | RS232 | RS485 | CAN | |
Communication Cascading Mode | RS485 | |||
RS232 protocol | ST BMS_protocol_2.0_20220616 | |||
Parallel RS485 protocol | ST BMS_protocol_2.0_20220616 | |||
UPS RS485 protocol | 1. PYLON low voltage Protocol RS485-V3.5 (2019-08-07) | |||
2. Voltronic Inverter and BMS 485 communication protocol for LIO-II (2022-01-18) | ||||
3. Growatt BMS RS485 Protocol for 1xSxxP ESS-V2.01 (2019-02-13) | ||||
4. Luxpowertek protocol for battery communication RS485 (2018-05-21) | ||||
5. PACE BMS Modbus Protocol for RS485-V1.3 (2017-06-27) | ||||
6. Sunpolo-6KW Inverter and BMS 485 communication protocol (2022-01-07) | ||||
UPS CAN protocol | 1. PYLON CAN BUS Protocol-V2.0.2 (2021-06-15) | |||
2. CAN BUS BMS Protocol (2021-01-07) | ||||
3. Growatt BMS CAN-Bus-protocol-low-voltage-V1.09 (2020-10-22) | ||||
4. GoodWe Low-voltage BMS Protocol CAN-V1.7 (2020-02-28) | ||||
5. SofarSolar Modbus communication protocol (2020-12-21) | ||||
6. MUST BMS CAN Bus Protocol-V2.0.2 (2021-06-02) |